IT IS FINALLY HERE! A Cap Hoop Package made specifically for the Brother SE-270D, the Brother SE-350, the Brother HE-120, the Brother HE-240, the Brother Innovis 500D and the Brother Innovis 900D! The Package Includes the Cap Hoop, 24 Prewound Bobbins, Embroidery Stork Scissors and a Polystar Sampler Thread Set, a retail value of over $115, for only $49.99!
IT IS FINALLY HERE! A Cap Hoop Package made specifically for the Brother SE-270D, the Brother SE-350, the Brother HE-120, the Brother HE-240, the Brother Innovis 500D and the Brother Innovis 900D! A Mr. Vac and Mrs. Sew Exclusive, we are happy to present to you a package including a Cap Hoop made for the Brother SE-270D, the Brother SE-350, the Brother HE-120, the Brother Innovis 500D and the Brother Innovis 900D ( A Retail Value of $50.00 ), Stork Embroidery Scissors ( A Retail Value of $17.95 ), 24 Prewound Bobbins ( A Retail Value of $19.99 ) and a Polystar Sampler Thread Set ( A Retail Value of $27.99 ), a grand total of over $115, for only $49.99!
 |
When you need scissors for that fine detail work, reach for this charming little stork. The needle sharp point can reach where others can't. Ideal for monogram work, applique, embroidery, ripping seams and trimming loose threads. This scissor is not only versatile but beautiful with it's gorgeous engraved gold-plated stork design. The stork scissors comes in a beautiful velvet case. |
Clamps to Embroidery Hoops
Clamps to 4" x 4" Embroidery Field Hoops.
Measurements of Cap Hoopster
The approximate embroiderable area of the Cap Hoop is 3.5" Long x 4 " Wide.
Ready to be Embroidered on in Seven Simple Steps
The Cap Hoop is easy and convenient to use. A Baseball cap can be hooped and ready to be embroidered in seven simple steps!
- Step 1- Pull shiny backing off of adhesive stabilizer. Adhere to the bottom of the Cap Hoopster. If the stabilizer has a hard time sticking, you may have to wrap around the edges of the Cap Hoopster.
- Step 2- Determine where the design will go on the cap. The use of a water-soluble pen will help center design. Just make sure a vertical and horizontal line intersecting at the center point of the design.
- Step 3- Loosen visor clamp by turning the thumbscrews. Attach the clear template with two holes to the two small pegs on the visor clamp. Loosen the back strap on cap and slide the visor under the template and visor clamp. Center the area of the cap that will be embroidered. The markings on the cap and the template will help you to do this.
- Step 4- Make sure sweat band is pulled back before you tighten down on the thumbscrews.
- a) You must prevent the sweatband from being stitched to the cap. Taping or pinning the sweat band may be necessary.
- b) Stand-up buckram (a non-fused backing) must be pulled back with sweatband. Cutting buckram liner an inch or two on each side, where it is stitched to the visor, will allow it to be pulled back neatly.
- Step 5- Press the cap down against the adhesive backing starting in the middle and working out. The cap must be as flat and smooth as possible.
- Step 6- Clamp the Cap Hoopster to the outer machine hoop.
- Step 7- Turn your machine on and set it up for embroidery as usual. Turn embroidery unit on and attach attach machine hoop. You may have to remove the foot and/or shank to do this. Use curser keys to center needle and begin to embroider designs onto the cap.
- * Note: Design May Need To Be Inverted
Specifications
The Cap Hoop will fit these machines:
- The Brother SE-270D
- The Brother SE-350
- The Brother HE-120
- The Brother HE-240
- The Brother Innovis 500D
- The Brother Innovis 900D
* Note: The above models only work with the 4" x 4" Embroidery Field Hoop.
Included Accessories
- Instructions for Using Hat Hoop
- Hat Hoop Template
Better
The same quality, strength, and value expected from the Polystar name, is finally available in prewound bobbins.
Incredible Value
Gorgeous bobbin thread, at an incredible value. You get 24 quality (95 meters each) prewound bobbins, a retail value of over $19 when your purchase this Cap Hoop Package.
Amount
This package includes 24 bobbins.
Length and Type
95 meters ea, 100% Spun Polyester Bobbin Thread, Style M
Color
The color of this product is white.
"Thread As Shiny As The Stars"
Both shiny and vibrant colors, create an amazing look to any project you are working on.
Unbelievable Strength
The most amazing thing about this thread is it's resistance to breakage, never again will you experience a breakage in thread in the middle of embroidering.
Weight of Thread
The weight of the thread is 50 wt, providing superior embroidery.
Set Includes
This set includes 7 spool set of 1,000 meter spool, of the shiniest polyester thread you have ever seen on true mini king spools.
Superior Shine and Strength
This thread has superior shine and superior strength. We are so excited to offer this thread. The thread sews out beautiful with so much shine! Best of all this thread is on mini king spools so the thread comes off the spool easy.
*Thread Colors may vary.
